LAN, Ethernet surge protection mounted on DIN rail, PTF-51-PRO/PoE/DIN
- Add feedback:
- Code: PTF-51-PRO/PoE/DIN
- Manufacturer's code: 5904041750380
- Weight: 0.1 kg
-
Availability:
Produkt available
(shipping withing 24-48h)
Surge protection to 100Mbit LAN network, designed to video surveillance, mounted on DIN rail, compatible with Ethernet 10Base-T i 100Base-T, PTF-51-PRO/PoE/DIN, manufacturer.
Surge protection for LAN / Ethernet with increased strength for high surge pulses, mounted on a 35mm DIN rail. It is designed for surge protection of devices operating in LAN networks, including IP cameras, PC computers, LAN switches, industrial automation controllers and buildings. Compatible with 10Base-T and 100Base-T Ethernet networks, using 5, 5e and 6th category cabling. Each conductor of LAN cable and PoE power circuit is protected against impacts up to 2kA, with direct discharge to the ground. High-quality printed circuits together with tuned differential pairs provide very good transmission parameters and contribute to the elimination of crosstalks that cause unstable LAN operation.
The product has been designed for installations in which at least one of the LAN end devices is outside the building or is otherwise exposed to heavy loads. Two protection stages with decoupling functionality, effectively eliminating overvoltages to the ground and transmission pairs inside.
A special protections circuit also protects LAN devices against voltage increase on PoE power lines in any of the possible standards (also transmitted on transmission lines). Lines 4-5 and 7-8 are interconnected because LAN 100Base-T uses them only to power PoE. The PTF-51-PRO protects both groups of power pairs against an increase in voltage above 58V and damage to the power supplies of LAN devices, such as switches or IP cameras. The power supply PoE transmitted through the limiter can be up to 60W (compatible with HiPoE).
The PTF-51-PRO/PoE/DIN ensures the continuity of the FTP cable shield between the input and output and additionally discharges the charge between shield and ground. Because it is recommended to ground the FTP cable shield only on one side, the shield on the protector side during normal operation is galvanically isolated at 90VDC.
The surge protection is mounted and grounded by a 35mm DIN rail. Use an unpainted DIN rail with adequate grounding that is able to remove shock loads to the ground from all mounted surge protection devies.
To protect one LAN cable , you can use two 1-channel protection devices mounted on the two ends of the LAN cable and ground them accordingly. In case of necessity of protection many LAN circuits, it is recommended to use multi-channel protection device on the side of the LAN switch and single-channel protectors on the side of end LAN devices.
If the PRO series surge protection is used at the external IP cameras, a minimum PRO-series protector should be used on the LAN switch side, otherwise LAN switch protection will be insufficient.
The PRO series surge protection devices should be not used with standard LAN patch panels with LSA (Krone type) connectors, because their strenth for high currents is very low and they will be damaged during strong surges. We suggest to use patch-panel based on Keystone type connectors.
PARAMETER |
NAME |
Data lines | |
---|---|
Supported channels | 1 |
Compatibility with Network | 10Base-T, 100Base-T, twisted pair 5, 5e, and 6th categories |
Input connector (Unprotected side) | RJ-45 |
Output connector (Protected side) | RJ-45 |
Rated Voltage DC (line-ground) UN | 90V DC |
Maximum voltage (line-ground) UC | 110V DC |
Protection level 1kV/μs (line-ground) UP | 600V |
Surge current (8/20µs, line-ground ) Iimp | 2,5kA per one conductor of a cable (12kA total) |
Rated Voltage DC (line-line) UN | 3,3V DC |
Maximum voltage (line-line) UC | 3,5V DC |
Protection level 1kV/μs (line-line) UP | 20V |
Surge current C1 (8/20µs, line-line ) Iimp | 100A |
Protected lines | 1-2, 3-6 |
Capacitnance (line-line) @1MHz | 6-15pF |
Capacitnance (line-ground) @1MHz | 1-2pF |
Series resistance | 2,2Ω / line |
Rated current IN | 300mA / line |
Protection level | 2 (GDT, TVS) |
Decouple element |
Surge resistor |
PoE protection | |
Rated Voltage DC (line-line) UN | 57V DC |
Maximum voltage(line-line) UC | 64V DC |
Protection level UP | 93V |
Surge current (8/20µs, line-line) Iimp | 100A |
Surge current (8/20µs, line-ground) Iimp | 2,5kA |
Protected pairs | (1+2)-(3+6), (4+5)-(7+8) |
Protected PoE standards | IEEE 802.3af/at/bt-type 3 (HiPoE, UPOE) |
Loss of PoE power in protection circuits |
IEEE 802.3af, option A: 0,23W @48VDC IEEE 802.3at, option A: 0,68W @54VDC IEEE 802.3bt, type 3 option AB: 0,8W @54VDC *) applies to full load |
Common features | |
Dimensions | 65 x 30 x 40 (mm) |
Application | Inside |
Mounting | Mounted on DIN rail |
Housing tightness | IP40 |
Operating temperature | -30ºC~60ºC |
Zakaz kopiowania i powielania treści! Powyższa treść zarezerwowana jest wyłącznie na użytek firmy Ewimar. Jeżeli chcesz umieścić produkt na swojej stronie, skontaktuj się z naszym Działem Handlowym w celu uzyskania treści ogólnodostępnej.